Email: sales@keepbestpcba.com
China & Thailand factoriesReplies within 24 hours

Pin-in-Paste vs Wave Soldering: Which Through-Hole PCB Assembly Method Wins?

Table of Contents

Pin-in-Paste Forms Through-Hole Joints During the Same Reflow Cycle as SMT Parts

When a mixed-technology board carries surface-mount components alongside a handful of through-hole connectors, headers, or electrolytic capacitors, the assembly engineer must decide how the through-hole joints will be formed. Pin-in-paste, also known as intrusive reflow, is a PCB assembly technique that deposits solder paste directly into the plated holes during the ordinary SMT stencil printing step, inserts the component leads into the Paste-filled holes, and then forms every joint on the board in a single reflow profile. Because it eliminates a dedicated wave soldering pass, this through-hole PCB assembly method has become a practical option for high-mix production. An experienced PCB assembly manufacturer weighs pin-in-paste against wave soldering on design rules, joint quality, and unit cost before committing a board to either route.

The decision is not simply about which machine is available. Pin-in-paste changes the design conversation: hole diameter, lead diameter, paste volume, and component height all have to be considered before stencil apertures are cut. Wave soldering, by contrast, is a mature bulk process that immerses the board underside in molten solder and is tolerant of a wider range of lead geometry. Understanding the process physics of each method is the first step toward choosing the right one for a specific product.

Wave Soldering Builds Through-Hole Connections in One High-Throughput Pass

Wave soldering remains the workhorse of through-hole PCB assembly. The populated board first passes through a flux applicator, then a preheat zone that activates the flux and brings the assembly up to temperature, and finally over a standing wave of molten solder. Capillary action draws solder up the plated barrel and around the lead, forming a fillet as the board leaves the wave. Because the entire underside is processed at once, wave soldering is extremely efficient for boards dominated by through-hole parts.

The process is well understood and supported by decades of IPC documentation. J-STD-001 and IPC-A-610 define the acceptable barrel fill and fillet appearance, and most contract facilities can hold these criteria with statistical process control. The main limitations are thermal exposure to the whole board, the need for fixtures or masks on boards that also carry bottom-side SMT parts, and the limited ability to process very fine lead pitches without bridging.

Pin-in-Paste and Wave Soldering Follow Fundamentally Different Process Flows

The clearest way to compare the two methods is to look at the route a board takes through the factory. Pin-in-paste is integrated into the surface-mount line: the board is printed, inspected, populated by pick-and-place, and reflowed once. Wave soldering is an added downstream operation after SMT reflow, requiring fluxing, preheating, and a molten solder pot. That difference drives cycle time, handling, and the number of thermal excursions the assembly must survive.

Process attribute Pin-in-paste (intrusive reflow) Wave soldering
Number of thermal profiles One shared SMT reflow profile Reflow plus a separate wave preheat and solder pass
Board handling Single pass through the SMT line Extra transfer, fixturing, and handling step
SMT bottom-side compatibility No second-wave exposure; bottom parts stay secure Bottom SMT parts need adhesive or selective masking
Flux chemistry Solder paste flux, no-clean or water-soluble Liquid flux spray or foam, often requiring cleaning
Changeover between jobs Stencil and feeder change only Wave pot setup, flux parameters, and fixture change

For low-volume, high-mix production, the single-pass nature of intrusive reflow is a real advantage. For a stable, high-volume board with many through-hole parts, the amortized cost of a wave line can still be lower.

Solder Joint Quality Depends on Hole Fill and Void Control in Both Methods

Both routes can produce IPC-A-610 Class 2 or Class 3 joints, but they reach that target differently. In a good pin-in-paste joint, sufficient paste volume fills at least seventy-five percent of the plated barrel and forms a concave fillet at both terminations. If the deposited volume is too low, the joint suffers insufficient hole fill; if it is too high, excess solder can ball or bridge on the topside. Because the paste flux is activated during reflow, wetting behavior is governed by the same profile that governs the surrounding SMT joints.

Wave solder joints are formed by molten solder wetting a preheated, flux-coated surface. Barrel fill is generally excellent, and the process is less sensitive to paste volume variation. However, the board experiences a second thermal shock, and the flux residue left under bottom-side components can be a reliability concern if the design calls for no-clean processes. For sealed or high-reliability assemblies, the ability of a one-stop PCBA solution to control cleaning, inspection, and traceability across both processes is often the deciding factor.

Design Rules Decide Whether Pin-in-Paste Succeeds on a Mixed-Technology Board

Pin-in-paste is less forgiving of poor layout than wave soldering. The geometry of the hole and the lead sets the paste volume that can be printed into the barrel, and the stencil aperture must be enlarged to deliver enough solder. Designers should treat the following rules as starting points and confirm them with the assembly house during DFM review:

  • Keep the annular gap between lead diameter and finished hole diameter small, typically 0.15 to 0.30 mm, so paste volume stays practical.
  • Use tented or plugged vias near through-hole pads to prevent solder wicking away from the joint during reflow.
  • Locate through-hole bodies so they do not shadow adjacent SMT parts during pick-and-place or reflow.
  • Provide adequate topside pad area and avoid thermal relief spokes that steal heat unevenly during reflow.
  • Confirm that the component body can tolerate the full SMT reflow temperature profile, especially for large electrolytic capacitors.

When these rules are respected, intrusive reflow can replace wave soldering on the majority of mixed-technology boards. When they are ignored, the resulting fill defects cost more in rework than the wave pass ever would.

Cost and Throughput Separate the Two Through-Hole PCB Assembly Methods

The business case for each method depends on volume and product mix. Pin-in-paste requires no wave soldering equipment, no solder pot maintenance, no flux management, and no separate fixture for most boards. It adds a stencil design step and may require a second print or a stepped stencil to deliver enough paste volume into holes. Wave soldering requires capital equipment, solder and flux consumables, dross management, and cleaning stations, but it processes a full panel in seconds once set up.

  • Low volume, frequent design changes: pin-in-paste usually wins on setup cost and lead time.
  • High volume, stable through-hole content: wave soldering usually wins on cycle time and per-unit cost.
  • Boards with bottom-side SMT: pin-in-paste avoids the extra adhesive or masking step that wave soldering demands.
  • Very small lead diameters or tight pitches: wave soldering reduces the risk of insufficient fill in the barrel.

A realistic cost comparison must include rework, inspection, and scrap, not just machine time. Many facilities find that the break-even point sits where through-hole component count and annual volume together justify a dedicated wave line.

Common Defects Reveal the Practical Limits of Each Through-Hole Method

Every through-hole PCB assembly process has a characteristic defect signature. Recognising it early lets engineers correct the root cause instead of adding manual touch-up. Pin-in-paste defects are usually traced back to paste volume, stencil release, or reflow profile. Wave soldering defects are usually traced back to flux activity, preheat temperature, conveyor speed, or solder chemistry.

  • Insufficient hole fill is the classic pin-in-paste fault, caused by undersized apertures or poor paste release into the barrel.
  • Solder balls and top-side bridging appear when paste volume is excessive or the reflow ramp is too aggressive.
  • Bridging and icicles dominate wave soldering when pitch is tight or conveyor speed and board angle are wrong.
  • Dewetting and grainy fillets in wave soldering point to insufficient preheat, weak flux, or contaminated solder.

Both methods benefit from process windows validated during NPI rather than adjusted reactively on the production floor.

How to Choose Between Pin-in-Paste and Wave Soldering for Your Board

The right choice starts with the board, not the equipment. Count the through-hole parts, note whether any sit on the bottom side, and check the lead-to-hole geometry against your stencil capability. If the board is SMT-dominant with only a few through-hole connectors, pin-in-paste keeps the route short and avoids a second thermal exposure. If the board is through-hole-dominant or carries press-fit connectors and large transformers, wave soldering remains the economical and robust choice.

Finally, consider the supplier. A facility that offers design-for-manufacturability review, solder paste and stencil engineering, AOI and X-ray inspection, and both reflow and wave lines can recommend the method based on data rather than convenience. That breadth is what turns a process comparison into a reliable production decision.

Summary

Pin-in-paste and wave soldering are two valid ways to build through-hole joints on a mixed-technology PCB. Pin-in-paste prints paste into the plated holes and forms all joints in one SMT reflow cycle, which shortens the route and suits low-volume, high-mix, SMT-dominant boards. Wave soldering adds a separate flux, preheat, and solder pass but delivers excellent barrel fill and low unit cost on stable, through-hole-heavy products.

The decision rests on lead-to-hole geometry, bottom-side SMT content, volume, and the supplier’s ability to control stencil design, reflow profiling, and inspection. When the design rules are respected, either method can meet IPC-A-610 Class 2 or Class 3 requirements.

FAQ

What is pin-in-paste in PCB assembly?

Pin-in-paste, or intrusive reflow, is a process that prints solder paste into plated through-holes during SMT stencil printing, inserts leads into the paste-filled holes, and forms all joints in one reflow cycle.

Can pin-in-paste replace wave soldering completely?

On many SMT-dominant mixed-technology boards, yes. It becomes less suitable when lead-to-hole gaps are large, through-hole count is very high, or components cannot tolerate the SMT reflow profile.

Which method gives better hole fill?

Wave soldering generally gives more consistent barrel fill across wide geometry. Pin-in-paste can match it when stencil apertures, paste volume, and reflow profile are engineered correctly.

Does pin-in-paste need a special stencil?

Often yes. Enlarged or stepped apertures are used to push enough paste into the holes, and nearby vias are tented to stop solder wicking during reflow.

Is wave soldering still relevant for modern PCB assembly?

Yes. It remains the most economical method for high-volume, through-hole-heavy boards and for connectors or large parts that are difficult to reflow.

How do I decide which process to use?

Evaluate through-hole component count, bottom-side SMT content, lead and hole dimensions, annual volume, and whether your assembly partner can support both routes with DFM and inspection capability.

Share :

Facebook
Twitter
LinkedIn
Pinterest

Get A Quote

Fill in your requirement information and upload Gerber and BOM files, we will give you a quote within 24 hours.

Get A quote

Fill in your requirement information and upload Gerber and BOM files, we will give you a quote within 24 hours.